Coding CLI 2 Switch dengan 2 VLan dan dihubungkan dengan Trunk

Temen-temen, inilah coding CLI dari 2 Switch yang kita buat tadi loh...

Coding CLI pada Swith 1 (Switch Tri)

Switch>enable

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#

Switch(config)#hostname SwitchTri

SwitchTri(config)#

SwitchTri(config)#vlan 2

SwitchTri(config-vlan)#name VLANku

SwitchTri(config-vlan)#exit

SwitchTri(config)#vlan 3

SwitchTri(config-vlan)#name VLANari

SwitchTri(config-vlan)#exit

SwitchTri(config)#

SwitchTri(config)#interface FastEthernet0/1

SwitchTri(config-if)#

SwitchTri(config-if)#

SwitchTri(config-if)#switchport access vlan 2

SwitchTri(config-if)#

SwitchTri(config-if)#exit

SwitchTri(config)#interface FastEthernet0/2

SwitchTri(config-if)#

SwitchTri(config-if)#

SwitchTri(config-if)#switchport access vlan 2

SwitchTri(config-if)#

SwitchTri(config-if)#exit

SwitchTri(config)#interface FastEthernet0/3

SwitchTri(config-if)#

SwitchTri(config-if)#

SwitchTri(config-if)#switchport access vlan 3

SwitchTri(config-if)#

SwitchTri(config-if)#exit

SwitchTri(config)#

%LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up

SwitchTri(config)#interface FastEthernet0/4

SwitchTri(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up

SwitchTri(config-if)#switchport mode trunk

SwitchTri(config-if)#

Coding CLI pada Swith 2 (Switch Yan)

Switch>enable

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#hostname SwitchYan

SwitchYan(config)#

SwitchYan(config)#vlan 2

SwitchYan(config-vlan)#name VLANku

SwitchYan(config-vlan)#exit

SwitchYan(config)#vlan 3

SwitchYan(config-vlan)#name VLANari

SwitchYan(config-vlan)#exit

SwitchYan(config)#

SwitchYan(config)#interface FastEthernet0/1

SwitchYan(config-if)#

SwitchYan(config-if)#

SwitchYan(config-if)#switchport access vlan 2

SwitchYan(config-if)#

SwitchYan(config-if)#exit

SwitchYan(config)#interface FastEthernet0/2

SwitchYan(config-if)#

SwitchYan(config-if)#

SwitchYan(config-if)#switchport access vlan 2

SwitchYan(config-if)#

SwitchYan(config-if)#exit

SwitchYan(config)#interface FastEthernet0/3

SwitchYan(config-if)#

SwitchYan(config-if)#

SwitchYan(config-if)#switchport access vlan 3

SwitchYan(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up